Laboratory and in-situ tests were carried out with the aim of investigating underground thermal properties and mechanisms of heat transfer of a pilot ground-source heat pump system consisting of two borehole heat exchangers. Samples of grouts used for filling the boreholes and of the main lithotypes penetrated by drilling were analysed in the lab for assessing their thermal properties. Grouts with different mechanical characteristics and similar mineral composition were used in the two holes. The grout thermal conductivity ranged from 1.65 to 2.13 W m−1K−1and thermal diffusivity from 0.61 to 0.80 μm2s−1. Thermophysical measurements on the lithotypes showed the largest thermal conductivity (2.66 W m−1K−1) in sandstones, whereas pelite denoted the lowest value (1.82 W m−1K−1). The average thermal diffusivity was 0.73 μm2s−1. The in-situ experiments included thermal logs, to evaluate the undisturbed underground temperature, and thermal response tests, which were interpreted with the moving line-source model to infer the underground thermal conductivity, the borehole thermal resistance and the groundwater velocity. The inferred thermal conductivity varied from 2.09 to 2.48 W m−1K−1and thermal resistance from 0.188 to 0.193 m K−1W−1. Values of Darcy velocity ranged from 5 to 9 × 10−7m s−1. After the heat injection tests, the temperature variation with time was recorded at 20-m-depth intervals in both holes. The temperature-time series were used to assess the thermal conductivity variation with depth. In both boreholes, thermal conductivity was little variable from 20 to 80 m depth (2.14–2.34 W m−1K−1) and it increased (2.49–2.68 W m−1K−1) at the hole bottom. The average thermal conductivity for the two boreholes was quite similar (2.29–2.32 W m−1K−1) and consistent with the values obtained with the moving line-source model. The results obtained with this approach were also consistent with the laboratory measurements and gave estimates of thermal conductivity at different depths.

Thermophysical parameters from laboratory measurements and in-situ tests in borehole heat exchangers

Verdoya, Massimo;Chiozzi, Paolo;
2018-01-01

Abstract

Laboratory and in-situ tests were carried out with the aim of investigating underground thermal properties and mechanisms of heat transfer of a pilot ground-source heat pump system consisting of two borehole heat exchangers. Samples of grouts used for filling the boreholes and of the main lithotypes penetrated by drilling were analysed in the lab for assessing their thermal properties. Grouts with different mechanical characteristics and similar mineral composition were used in the two holes. The grout thermal conductivity ranged from 1.65 to 2.13 W m−1K−1and thermal diffusivity from 0.61 to 0.80 μm2s−1. Thermophysical measurements on the lithotypes showed the largest thermal conductivity (2.66 W m−1K−1) in sandstones, whereas pelite denoted the lowest value (1.82 W m−1K−1). The average thermal diffusivity was 0.73 μm2s−1. The in-situ experiments included thermal logs, to evaluate the undisturbed underground temperature, and thermal response tests, which were interpreted with the moving line-source model to infer the underground thermal conductivity, the borehole thermal resistance and the groundwater velocity. The inferred thermal conductivity varied from 2.09 to 2.48 W m−1K−1and thermal resistance from 0.188 to 0.193 m K−1W−1. Values of Darcy velocity ranged from 5 to 9 × 10−7m s−1. After the heat injection tests, the temperature variation with time was recorded at 20-m-depth intervals in both holes. The temperature-time series were used to assess the thermal conductivity variation with depth. In both boreholes, thermal conductivity was little variable from 20 to 80 m depth (2.14–2.34 W m−1K−1) and it increased (2.49–2.68 W m−1K−1) at the hole bottom. The average thermal conductivity for the two boreholes was quite similar (2.29–2.32 W m−1K−1) and consistent with the values obtained with the moving line-source model. The results obtained with this approach were also consistent with the laboratory measurements and gave estimates of thermal conductivity at different depths.
File in questo prodotto:
File Dimensione Formato  
Appl. Thermal Engineering 2018.pdf

accesso chiuso

Tipologia: Documento in versione editoriale
Dimensione 1.74 MB
Formato Adobe PDF
1.74 MB Adobe PDF   Visualizza/Apri   Richiedi una copia

I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/11567/925028
Citazioni
  • ???jsp.display-item.citation.pmc??? ND
  • Scopus 17
  • ???jsp.display-item.citation.isi??? 16
social impact